Canted Valve Series/14°

 

 

CV SP 265 Intake

Image 2 of 2

 

 

[tabs title=”” type=””]
[tab title=”Description”]
The BRODIX canted valve is in a league of its own and is still one of the best flowing small block heads available.
This head has valve angles of 14° and 4° on the intake and 10° and 2° on the exhaust. The canted valve cylinder head is best used with racing gas.
The intake may easily flow over 400 cfm with the exhaust port flowing in the 250 cfm range when completely ported. An extremely high intake port and a tall, radiused intake short side are just a few of the features of this state-of-the-art cylinder head.
[/tab]
[tab title=”Details”]

Package Heads

Facts and Related Components

• PS CB:
Valve Bowls Blended• PS MI:
Match Intake Port to BRODIX MG 1901
(CV SP 265)
Match Intake Port to FP 89271
(CV SP 330)

• PS Valve Job:
Competition Valve Job

• Intake Valves:
2.200 x 6.200 o.a.l. – BX 2200-620T
(CV SP 265)
2.250 x 6.200 o.a.l. – BX 2250-620T
(CV SP 330)

• Exhaust Valves:
1.600 x 6.090 o.a.l. – BR 91600

• Valve Springs:
1.550 Roller Valve Spring – GA 1000,
240 lb Closed, 550 lb Open,
1.950 Installed Height,
.700 Maximum Lift

• Retainers:
1.550 10° Titanium – MA 2398BR

• Valve Locks:
10° Jumbo – CC 611

• Rocker Studs:
Shaft System Required

• Valve Seals:
11/32 – US VS529V

• Torque Heads:
70 ft-lb • Torque Rocker Studs:
40-45 ft-lb

• Intake Gaskets:
BRODIX MG 1901 (CV SP 265)
FEL-PRO 89271 (CV SP 330)

• Head Gaskets:
350 – FEL-PRO 1003, COMETIC C5399
400 – FEL-PRO 1004, COMETIC C5403

• Exhaust Gaskets:
Spread Port – BRODIX MG 52464,
COMETIC C5424

• Head Studs:
ARP 234-4312 (12 pt)

• Accessory Bolt Holes Are Drilled:

• Spark Plug Starting Points:
NGK R5671A-10 for Alcohol
NGK R5671A-9 for Racing Gas

• Spring Pockets:
1.550 Out of the Box;
Call BRODIX Before Installing
1.625 Springs (Center Springs May Hit)

• Valve Angle:
14° and 4° Intake,
10° and 2° Exhaust

• Angle Milling:
Not Available

• Flat Milling:
.0050 in Per cc

• Angle Machining:
Not Available

• Pushrod Slots:
Left Bare and Uncut

• Stud Girdle:
Not Available

• Rocker Arms:
Shaft System – T&D 2240,
JESEL KPS 06048

• Lifters:
.180 Offset

• Pistons:
Special for BRODIX Canted Valve

• Pushrods:
Special Length

• Valve Covers:
VC 190

• Special Tools:
MS MAC – Torque Upper Row of Head Studs

• Center Two Head Stud Nuts:
BR CV CN

• Center Two Exhaust Springs Must be Removed
While Torquing Heads

• Intake Manifold:
HV 1900

[/tab]
[tab title=”Flow Chart”]

Flow Chart cfm @ 28″ H20

 
Valve Size

0.200

0.300

0.400

0.500

0.600
      0.650      0.700
CV SP 265
(Hand Ported)		2.200 Intake159232293347379389395
1.600 Exhaust109145188221237239244
CV SP 330
(Hand Ported)		2.250 Intake165243305350376383392
1.600 Exhaust116158193234245249254

[/tab]
[tab title=”Easy Order Numbers & More”]

Basic Easy Order Numbers

Part#Easy
Order #		Port
Vol.		Cham.
Vol.		Int/Ext
Valve 		Spring
Seat
Pressure		Spring
Diam.		Ret.
ST/TI		Per
CV SP 265 Bare1140000265 cc54 cc    2
CV SP 330 Bare
114001330 cc54 cc     2
CV SP 265 Pkg1141000265 cc54 cc2.200 / 1.600 1.550TI2
CV SP 330 Pkg1141001330 cc54 cc2.200 / 1.600 1.500TI1
CV SP Special1149000Custom Order54 cc    2

[/tab]
[tab title=”Instruction Sheet”]

smallblockheadinstructions
[/tab]
[/tabs]