• PS CB:
Valve Bowls Blended• PS MI:
Match Intake Port to FP 1206
(CH)Match Intake Port to FP 1262
(FO)
Match Intake Port to FP 1213
(MO)
• PS Valve Job:
Competition Valve Job
• Intake Valves:
2.080 x 4.965 o.a.l. – BR 81019
(FO)
2.080 x 5.065 o.a.l. – BR 60029
(CH or MO)
• Exhaust Valves:
1.600 x 4.965 o.a.l. – BR 81021
(FO)
1.600 x 5.065 o.a.l. – BR 60030
(CH or MO)
• Valve Springs:
1.550 Roller Valve Spring – PAC 1941,
255 lb Closed, 610 lb Open,
1.950 Installed Height,
.700 Maximum Lift
• Retainers:
1.550 10° Titanium – MA 2398 BR
• Valve Locks:
10° Jumbo – CC 611
• Rocker Studs:
7/16 – BR 716L, AR RRS-4I
(CH or FO)
Shaft System Required
(MO)
• Guide Plates:
5/16 – BR 5160
(CH)
5/16 – BR 289351
(FO)
Not Available
(MO)
• Valve Seals:
11/32 – US VS529V |
• Torque Heads:
70 ft-lb with 7/16″ Studs• Torque Rocker Studs:
40-45 ft-lb
(CH or FO)
• Torque Rocker Shaft:
30 ft-lb
(MO)
• Intake Gaskets:
FEL-PRO 1206
(CH)
FEL-PRO 1262
(FO)
FEL-PRO 1213
(MO)
• Head Gaskets:
350 – FEL-PRO 1003
(CH)
FEL-PRO 1011-1 or FEL-PRO 1011-2
(FO)
FEL-PRO 1008
(MO)
• Exhaust Gaskets:
BRODIX MG 1500, COMETIC C5424
(CH)
BRODIX MG 1351
(FO, “N” Bolt Pattern)
FEL-PRO 1413
(MO)
• Head Studs:
ARP 234-4301
(CH)
ARP 154-4203
(FO)
ARP 144-4204
(MO)
• Accessory Bolts Holes Are Drilled Except on (MO)
27-222/B1 BA SUPR
• Spark Plug Starting Points:
NGK R5671A-9
for Alcohol
NGK R5671A-8
for Racing Gas
• Spring Pockets:
May Not be Cut Any Larger
or Deeper Than 1.550
• Valve Angle:
23° (CH)
20° (FO)
18° (MO)
• Angle Milling:
.0078 in Per cc
(CH)
Not Available
(FO or MO)
• Flat Milling:
.0060 in Per cc
(CH or FO)
.0055 in Per cc
(MO)
• Angle Machining:
Not Available
• Dowel Shift:
Not Available
• Pushrod Slots:
40/60 Spacing
(CH)
53/119 Spacing
(FO)
Special
(MO)
• Stud Girdle:
40/60 BRODIX 6440
(CH)
53/119 BRODIX BR 6430
(FO)
Shaft Sysem Required
(MO)
• Rocker Arms:
Standard (CH or FO)
Shaft System Required (MO) – T&D 8019,
JESEL KPS 248102
• Lifters:
Standard
• Pushrods:
Special Length |
