• PS CB:
Valve Bowls Blended• PS MI:
Match Intake Port to FP 1204 (IK 180)
Match Intake Port to FP 1206 (IK 200, IK 215)
Match Intake Port to FP 1205 (BP IK 210)• PS Valve Job:
Competition Valve Job• Intake Valves:
2.020 x 4.920 o.a.l. – BR 6170DI (IK 180, IK 200)
2.080 x 4.965 o.a.l. – BR 81019 (IK 215, BP IK 210) • Exhaust Valves:
1.600 x 4.920 o.a.l. – BR 6169DI (IK 180, IK 200)
1.600 x 4.965 o.a.l. – BR 81021 (IK 215, BP IK 210) • Valve Springs:
1.250 Hydraulic Valve Spring – CC 981,
100 lb Closed, 300 lb Open,
1.850 Installed Height,
.525 Maximum Lift
(IK 180, IK 200) 1.470 Hydraulic Roller Valve Spring – CC 987,
125 lb Closed, 325 lb Open,
1.900 Installed Height,
.575 Maximum Lift
(IK 180, IK 200) 1.550 Flat Tappet Valve Spring – BT 120121,
150 lb Closed, 365 lb Open,
1.950 Installed Height,
.600 Maximum Lift
(IK 215, BP IK 210) 1.550 Roller Valve Spring – PAC 1941,
255 lb Closed, 610 lb Open,
1.950 Installed Height,
.700 Maximum Lift
(IK 215, BP IK 210) • Retainers:
1.250 7° Steel – CC 742 (IK 180, IK 200)
1.430 7° Steel – CC 743 (IK 180, IK 200)
1.550 10° Steel – CC 752 (IK 215, BP IK 210) • Valve Locks:
7° – PI PF – 555 (IK 180, IK 200)
10° – Jumbo – CC 611 (IK 215, BP IK 210) • Rocker Studs:
3/8 – BR 318S (IK 180, IK 200)
7/16 – BR 716L, AR RSS-4I (IK 215, BP IK 210) • Guide Plates:
5/16 – CC 4808 • Valve Seals:
11/32 – US VS529V | • Torque Heads:
70 ft-lb• Torque Rocker Studs:
40-45 ft-lb• Intake Gaskets:
FEL-PRO 1204, COMETIC C5416 (IK 180)
FEL-PRO 1206, COMETIC C5414 (IK 200, IK 215)
FEL-PRO 1205 (BP IK 210)• Head Gaskets:
350 – FEL-PRO 1003, COMETIC C5399
400 – FEL-PRO 1004, COMETIC C5403 • Exhaust Gaskets:
FEL-PRO 1404, COMETIC C5415
(IK 180, IK 200)
FEL-PRO 1406, COMETIC C5415
(IK 215, BP IK 210) • Head Bolts:
ARP 134-3601, MANLEY 42313 • Head Bolt Washers:
MANLEY 42102 • Head Studs:
ARP 134-4001 (6pt) • Accessory Bolt Holes Are Drilled • Spark Plug Starting Points:
CHAMPION RN12YC or AUTOLITE 3924
for Pump Gas
NGK R5671A-8
for Racing Gas • Intake Valve Seats:
DBP 2.131 5/16 • Exhaust Valve Seats:
DBP 1.650 3/8 • Intake and Exhaust Valve Guides:
SMG 545 11/32 CM • Spring Pockets:
May Not be Cut Any Larger
or Deeper Than 1.550 • Valve Angle:
23° • Angle Milling:
.0078 in per cc • Flat Milling:
.0060 in per cc • Angle Machining:
Not Available • Dowel Shift:
Not Available • Pushrod Slots:
Standard • Stud Girdle:
BR 6435 • Rocker Arms:
Standard • Lifters:
Standard • Valve Centerline:
Standard • Intake Manifold:
HP-1 / HV 1016 (IK 180) HV 1014 / HV 1016 (IK 200 , IK 210, IK 215) BM 1000 (IK 215) |
